--------------------- 88DESIGN SPORTS --------------------- ジムニーのモータースポーツユーザー向け 追加メーター用パネルキットです。 0DINパネルキットをベースにしているため、 純正2DINパネルと比較して前方および 下方視界が大きく改善し、オフロードでも オンロードでもドライビングに集中する ことができます。 またメーターフードを上に20°、右に10°傾斜させ、 メータークラスターと同じ高さで車両中央に 設置することで、ドライビング中に視線を大きく 動かすことなくメーターを視認することができます。 ※ 適合車種：JB64/JB74/JC74 右ハンドル車 ※ メーターフード内径はφ62です。 　メーター本体はスポンジテープ等で固定してください ※ メーターフード：PA12（ナイロン）製 　 パネル本体：PP（ポリプロピレン）製 ※ 完全受注生産品につき、ご注文をいただいてから 　 お届けまで2〜3週間ほどお時間をいただきます。 This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether on-road or off-road. Additionally, by tilting the gauge hood 20° upward and 10° to the right, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB64/JB74/JC74 Right-Hand Drive * The inner diameter of the meter hood is φ62. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until delivery.

--------------------- 88DESIGN SPORTS --------------------- ジムニーのモータースポーツユーザー向け 追加メーター用パネルキットです。 0DINパネルキットをベースにしているため、 純正2DINパネルと比較して前方および 下方視界が大きく改善し、オフロードでも オンロードでもドライビングに集中する ことができます。 またメーターフードを上に20°、右に10°傾斜させ、 メータークラスターと同じ高さで車両中央に 設置することで、ドライビング中に視線を大きく 動かすことなくメーターを視認することができます。 ※ 適合車種：JB64/JB74/JC74 右ハンドル車 ※ メーターフード内径はφ54です。 　メーター本体はスポンジテープ等で固定してください ※ メーターフード：PA12（ナイロン）製 　 パネル本体：PP（ポリプロピレン）製 ※ 完全受注生産品につき、ご注文をいただいてから 　 お届けまで2〜3週間ほどお時間をいただきます。 This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether on-road or off-road. Additionally, by tilting the gauge hood 20° upward and 10° to the right, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB64/JB74/JC74 Right-Hand Drive * The inner diameter of the meter hood is φ54. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until delivery.

--------------------- 88DESIGN SPORTS --------------------- ジムニーのモータースポーツユーザー向け 追加メーター用パネルキットです。 0DINパネルキットをベースにしているため、 純正2DINパネルと比較して前方および 下方視界が大きく改善し、オフロードでも オンロードでもドライビングに集中する ことができます。 またメーターフードを上に20°、右に10°傾斜させ、 メータークラスターと同じ高さで車両中央に 設置することで、ドライビング中に視線を大きく 動かすことなくメーターを視認することができます。 ※ 適合車種：JB64/JB74/JC74 右ハンドル車 ※ メーターフード内径はφ62です。 　メーター本体はスポンジテープ等で固定してください ※ メーターフード：PA12（ナイロン）製 　 パネル本体：PP（ポリプロピレン）製 ※ 完全受注生産品につき、ご注文をいただいてから 　 お届けまで2〜3週間ほどお時間をいただきます。 This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether on-road or off-road. Additionally, by tilting the gauge hood 20° upward and 10° to the right, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB64/JB74/JC74 Right-Hand Drive * The inner diameter of the meter hood is φ62. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until delivery.

--------------------- 88DESIGN SPORTS --------------------- ジムニーのモータースポーツユーザー向け 追加メーター用パネルキットです。 0DINパネルキットをベースにしているため、 純正2DINパネルと比較して前方および 下方視界が大きく改善し、オフロードでも オンロードでもドライビングに集中する ことができます。 またメーターフードを上に20°、右に10°傾斜させ、 メータークラスターと同じ高さで車両中央に 設置することで、ドライビング中に視線を大きく 動かすことなくメーターを視認することができます。 ※ 適合車種：JB64/JB74/JC74 右ハンドル車 ※ メーターフード内径はφ54です。 　メーター本体はスポンジテープ等で固定してください ※ メーターフード：PA12（ナイロン）製 　 パネル本体：PP（ポリプロピレン）製 ※ 完全受注生産品につき、ご注文をいただいてから 　 お届けまで2〜3週間ほどお時間をいただきます。 This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether on-road or off-road. Additionally, by tilting the gauge hood 20° upward and 10° to the right, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB64/JB74/JC74 Right-Hand Drive * The inner diameter of the meter hood is φ54. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until delivery.

--------------------- 88DESIGN SPORTS --------------------- ジムニーのモータースポーツユーザー向け 追加メーター用パネルキットです。 0DINパネルキットをベースにしているため、 純正2DINパネルと比較して前方および 下方視界が大きく改善し、オフロードでも オンロードでもドライビングに集中する ことができます。 またメーターフードを上に20°、右に10°傾斜させ、 メータークラスターと同じ高さで車両中央に 設置することで、ドライビング中に視線を大きく 動かすことなくメーターを視認することができます。 本商品はメーターを1個追加するパネルです。 メーター位置（右 or 中央 or 左）を選択してください。 ※ 適合車種：JB64/JB74/JC74 右ハンドル車 ※ メーターフード内径はφ62です。 　メーター本体はスポンジテープ等で固定してください ※ メーターフード：PA12（ナイロン）製 　 パネル本体：PP（ポリプロピレン）製 ※ 完全受注生産品につき、ご注文をいただいてから 　 お届けまで2〜3週間ほどお時間をいただきます。 This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether on-road or off-road. Additionally, by tilting the gauge hood 20° upward and 10° to the right, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB64/JB74/JC74 Right-Hand Drive * The inner diameter of the meter hood is φ62. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until delivery.

--------------------- 88DESIGN SPORTS --------------------- ジムニーのモータースポーツユーザー向け 追加メーター用パネルキットです。 0DINパネルキットをベースにしているため、 純正2DINパネルと比較して前方および 下方視界が大きく改善し、オフロードでも オンロードでもドライビングに集中する ことができます。 またメーターフードを上に20°、右に10°傾斜させ、 メータークラスターと同じ高さで車両中央に 設置することで、ドライビング中に視線を大きく 動かすことなくメーターを視認することができます。 本商品はメーターを1個追加するパネルです。 メーター位置（右 or 中央 or 左）を選択してください。 ※ 適合車種：JB64/JB74/JC74 右ハンドル車 ※ メーターフード内径はφ54です。 　メーター本体はスポンジテープ等で固定してください ※ メーターフード：PA12（ナイロン）製 　 パネル本体：PP（ポリプロピレン）製 ※ 完全受注生産品につき、ご注文をいただいてから 　 お届けまで2〜3週間ほどお時間をいただきます。 This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether on-road or off-road. Additionally, by tilting the gauge hood 20° upward and 10° to the right, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB64/JB74/JC74 Right-Hand Drive * The inner diameter of the meter hood is φ54. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until delivery.

--------------------- 88DESIGN SPORTS --------------------- ジムニーのモータースポーツユーザーはもちろん、 ストリートユーザーにもおすすめ、 クラッチペダルエクステンダーです。 そのシートポジション、クラッチ基準になっていませんか？ 本来はブレーキペダルを踏み込んだ状態で 右膝が少し曲がる位置が理想です。 しかしクラッチの切れる位置が深いので、 どうしても理想の位置より少し前にいきがち。 クラッチペダルゴムを取り外して本商品を間に挟むことで、 踏み込んだときのブレーキペダルとの高さの差が少なくなり、 シートを1〜2ノッチ後ろに下げることができます。 また、クラッチペダルをしっかりと踏み切れることで ギヤ鳴りを防ぎ、シンクロの保護にもなります。 純正ペダルおよびペダルゴムに無加工で取り付け可能です。 ※ 適合車種：JB64/JB74/JC74 MT車 ※ ペダルリフト量：12mm（標準） ※ 材質：PA12（ナイロン）製 ※ カラー：オレンジ ※ 完全受注生産品につき、ご注文をいただいてから 　 お届けまで1〜2週間ほどお時間をいただきます。 This clutch pedal extender is recommended not only for Jimny motorsports enthusiasts, but also for street drivers. Is your seat position based on the clutch position? Ideally, your right knee should be slightly bent when you have your foot on the brake pedal. However, because the clutch disengages at a deep position, you tend to sit slightly forward of the ideal position. By removing the clutch pedal rubber and inserting this product in between, the height difference between the clutch and brake pedals when depressed is reduced, allowing you to move your seat back by 1 to 2 notches. Additionally, being able to fully depress the clutch pedal prevents gear noise and helps protect the synchros. It can be installed without any modifications to the stock pedal or pedal rubber. * Compatible Models: JB64/JB74/JC74 MT vehicles * Pedal Lift: 12mm (Standard) * Material: PA12 (Nylon) * Color: Orange * As this is a made-to-order item, please allow 1–2 weeks from the time of your order until delivery.

--------------------- 88DESIGN SPORTS --------------------- ジムニーのモータースポーツユーザーはもちろん、 ストリートユーザーにもおすすめ、 クラッチペダルエクステンダーです。 そのシートポジション、クラッチ基準になっていませんか？ 本来はブレーキペダルを踏み込んだ状態で 右膝が少し曲がる位置が理想です。 しかしクラッチの切れる位置が深いので、 どうしても理想の位置より少し前にいきがち。 クラッチペダルゴムを取り外して本商品を間に挟むことで、 踏み込んだときのブレーキペダルとの高さの差が少なくなり、 シートを1〜2ノッチ後ろに下げることができます。 また、クラッチペダルをしっかりと踏み切れることで ギヤ鳴りを防ぎ、シンクロの保護にもなります。 純正ペダルおよびペダルゴムに無加工で取り付け可能です。 ※ 適合車種：JB64/JB74/JC74 MT車 ※ ペダルリフト量：20mm 　（小柄な方や繊細な操作を必要とする方におすすめ） ※ 材質：PA12（ナイロン）製 ※ カラー：オレンジ ※ 完全受注生産品につき、ご注文をいただいてから 　 お届けまで1〜2週間ほどお時間をいただきます。 This clutch pedal extender is recommended not only for Jimny motorsports enthusiasts, but also for street drivers. Is your seat position based on the clutch position? Ideally, your right knee should be slightly bent when you have your foot on the brake pedal. However, because the clutch disengages at a deep position, you tend to sit slightly forward of the ideal position. By removing the clutch pedal rubber and inserting this product in between, the height difference between the clutch and brake pedals when depressed is reduced, allowing you to move your seat back by 1 to 2 notches. Additionally, being able to fully depress the clutch pedal prevents gear noise and helps protect the synchros. It can be installed without any modifications to the stock pedal or pedal rubber. * Compatible Models: JB64/JB74/JC74 MT vehicles * Pedal Lift: 20mm (Standard) * Material: PA12 (Nylon) * Color: Orange * As this is a made-to-order item, please allow 1–2 weeks from the time of your order until delivery.

--------------------- 88DESIGN SPORTS --------------------- This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether off-road or on-road. Additionally, by tilting the gauge hood 20° upward and 10° to the left, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB74/JC74 Left-Hand Drive * The inner diameter of the meter hood is φ62. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until shipment. However, our international shipping system is configured to automatically cancel orders if they are not shipped within 10 days of placement. Therefore, if you are interested in purchasing this item, please contact us in advance at this email address ([email protected]). We will notify you as soon as the item is ready for shipment, and we would appreciate it if you could place your order at that time. * The images shown are right-hand drive version that have been flipped horizontally. (This is because left-hand drive vehicles are not available in Japan.)

--------------------- 88DESIGN SPORTS --------------------- This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether off-road or on-road. Additionally, by tilting the gauge hood 20° upward and 10° to the left, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB74/JC74 Left-Hand Drive * The inner diameter of the meter hood is φ54. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until shipment. However, our international shipping system is configured to automatically cancel orders if they are not shipped within 10 days of placement. Therefore, if you are interested in purchasing this item, please contact us in advance at this email address ([email protected]). We will notify you as soon as the item is ready for shipment, and we would appreciate it if you could place your order at that time. * The images shown are right-hand drive version that have been flipped horizontally. (This is because left-hand drive vehicles are not available in Japan.)

--------------------- 88DESIGN SPORTS --------------------- This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether off-road or on-road. Additionally, by tilting the gauge hood 20° upward and 10° to the left, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB74/JC74 Left-Hand Drive * The inner diameter of the meter hood is φ62. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until shipment. However, our international shipping system is configured to automatically cancel orders if they are not shipped within 10 days of placement. Therefore, if you are interested in purchasing this item, please contact us in advance at this email address ([email protected]). We will notify you as soon as the item is ready for shipment, and we would appreciate it if you could place your order at that time.

--------------------- 88DESIGN SPORTS --------------------- This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether off-road or on-road. Additionally, by tilting the gauge hood 20° upward and 10° to the left, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB74/JC74 Left-Hand Drive * The inner diameter of the meter hood is φ54. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until shipment. However, our international shipping system is configured to automatically cancel orders if they are not shipped within 10 days of placement. Therefore, if you are interested in purchasing this item, please contact us in advance at this email address ([email protected]). We will notify you as soon as the item is ready for shipment, and we would appreciate it if you could place your order at that time.

--------------------- 88DESIGN SPORTS --------------------- This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether off-road or on-road. Additionally, by tilting the gauge hood 20° upward and 10° to the left, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB74/JC74 Left-Hand Drive * The inner diameter of the meter hood is φ62. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until shipment. However, our international shipping system is configured to automatically cancel orders if they are not shipped within 10 days of placement. Therefore, if you are interested in purchasing this item, please contact us in advance at this email address ([email protected]). We will notify you as soon as the item is ready for shipment, and we would appreciate it if you could place your order at that time.

--------------------- 88DESIGN SPORTS --------------------- This is a panel kit for additional gauges designed for Jimny motorsports enthusiasts. Based on a 0DIN panel kit, it significantly improves forward and downward visibility compared to the stock 2DIN panel, allowing you to concentrate on driving whether off-road or on-road. Additionally, by tilting the gauge hood 20° upward and 10° to the left, and mounting it at the same height as the gauge cluster in the center of the vehicle, you can read the gauges without having to move your line of sight significantly while driving. * Compatible Models: JB74/JC74 Left-Hand Drive * The inner diameter of the meter hood is φ54. Please secure the meter unit using foam tape or similar. * Meter Hood: Made of PA12 (Nylon) Panel Body: Made of PP (Polypropylene) * As this is a made-to-order product, please allow approximately 2–3 weeks from the time of your order until shipment. However, our international shipping system is configured to automatically cancel orders if they are not shipped within 10 days of placement. Therefore, if you are interested in purchasing this item, please contact us in advance at this email address ([email protected]). We will notify you as soon as the item is ready for shipment, and we would appreciate it if you could place your order at that time.